menu

Delivery of goods exclusively through retailers. Prices incl. VAT.

Grid List

Set Descending Direction

6 Item(s)

Delivery of goods exclusively through retailers. Prices incl. VAT.

Grid List

Set Descending Direction

6 Item(s)

Electric Trim Tab systems Basic without Indicator
Electric Trim Tab systems with powerful 12V DC motor (24V upon request) Total travel in 8 seconds. Stainless Steel (Aisi 304) trim tabs (2,8mm thickness). Very simple mounting: no hydraulic oil, no oil pump! Comes complete with all fitting materials.

Item Code clarification: e.g. 047 12 24
12 = depth 12”
24 = width at the transom 24” (1” = 2,54cm)

Wiring length 6’ (1,8m) per actuator and 20’ (6m) wiring loom. Complete with watertight control panel with trim tab position indicator. Trim tabs go automatically to “0”- position after contact switch off. The control panel is suitable for 12V & 24V. The control unit is in the control panel. No interface box needed!

Retrofit of a Bennet® Trim Tab System?
These kits are also suitable as an upgrade-kit for older Bennet® hydraulic systems with 12” cylinders. You have to remove the hydraulic cylinders, control panel, hydraulic pump, hoses and upper cylinder bracket. The existing Trim Tab and lower bracket with pin will be used again.

Electric Trim Tab system with Automatic Leveling Control 1 Helm position (1 Control panel)
As wind shifts, water conditions change or passengers move about, the Automatic Leveling Control (ALC) will automatically adjust your trim tabs to maintain a level boat for a more comfortable and enjoyable ride. The ALC automatically corrects the roll from side to side and pitch from fore to aft to enhance your boating experience and improve your fuel economy!

Features:
• 10-30V
• Microprocessor based automatically levelling control with LED tab positions indicators
• Automatically dims LED tab position indicators in darkness and brightens in sunlight
• Controls roll and pitch automatically
• Interne GPS, no GPS antenna or network required
• Automatically adapts to varying sea conditions
• UV protected - will not deteriorate in sunlight
• Designed for planing and semi-planing hulls largen than 20’
• Actuators connect directly to (no external power module box required)
• Automatically retracts trim tabs when boat is off plane or using optional key switch connection
• Dual station (fly-bridge) operation available
Even under acceleration the ALC will automatically adjust!

 

Electric Trim Tab systems with indicator
Electric Trim Tab systems with powerful 12V* DC motor, Stainless Steel (Aisi 304) trim tabs (2,8mm thickness). Very simple mounting: no hydraulic oil, no oil pump! Just electric wires and a junction block. Comes complete with all fitting materials. Wiring length 6’ (1,8m) per actuator and 20’ (6m) wiring loom. Complete with watertight control panel with trim tab position indicator. Trim tabs go automatically to “0”- position after contact switch off. This control panel is suitable for 12V & 24V. The control unit is in the control panel. No interface box needed!

Item Code explained: e.g. 047 12 24/M
12 = Trim tap depth 12”
24 = Trim tab width at transom 24” (1”= 2,54cm)
All kits have 1 actuator per trim tab.

Dims. control panel: (Item Code 0470002): 100 x 85mm (w x h).

These electric trim tab systems are also suitable as upgradekit for old hydraulic systems of Bennett® with 12” actuators. You just have to replace the old hydraulic actuators, control panel, hydraulic pump, hydraulic tubes and the upper actuator bracket. The existing Bennett® trim tabs, the lower actuator bracket and bracket pin will remain.

 

SMART TABS SX105
Bigger SX - SMART TABS for boats up to 25’ (7,6m)
SMART TABS utilize Nitrogen Gas filled Actuators to hold the trim plates down during low speed operation and allow the water to “automatically” push the plates up (horizontal) at higher speeds. The tabs remain under a load creating die control like shock absorbers. No need to worry about tab position.

Features:
• Tabs and actuators made of corrosion free molded composite materials
• Tabs have tracking ribs to improve handling at higher speeds
• Tab size 9,5”x 10” (241 x 254mm)
• Smoother and faster acceleration (great for skiing)
• 40% less Bow Rise and 35% lower on plane speed (great for tubing)
• More Top Speed and No Porpoising or Chine Walking
• Improves Handling and Smoother Ride in any water
• Improved fuel economy (up to 11% less)
• Assembly & Installation in Minutes

 

SMART TABS SX95
The patented SMART TABS are a one of a kind trim and stabilizer system that automatically adjusts to the sea conditions, without the need for expensive electric or hydraulic hardware and switches. SMART TABS utilize Nitrogen Gas filled Actuators to hold the trim plates down during low speed operation and allow the water to “automatically” push the plates up (horizontal) at higher speeds. The tabs remain under a load creating ride control like shock absorbers. No need to worry about tab position. The system constantly reacts to the water conditions, boat speed and balance providing a remarkable improvement on any boat.

Features:
• Tabs and actuators made of corrosion free molded composite materials
• Tabs have tracking ribs to improve handling at higher speeds
• Tab size 9,5”x 10” (241 x 254mm)
• Smoother and faster acceleration (great for skiing) 40% less Bow Rise and 35% lower on plane speed (great for tubing)
• More Top Speed and No Porpoising or Chine Walking
• Improves Handling and Smoother Ride in any water
• Improved fuel economy (up to 11% less)
• Assembly & Installation in Minutes

Index

Select the first letter of the product you are looking for